Best Garden Hoses 2017

Snakes are extension cords, because the first problem should always be length. Should measure the distance from axle to all of the places where you will need a hose. If this distance exceeds a hundred feet, you can either buy hose industrial, or buy two or more tubes, which you, in turn, to communicate with each other. It should be borne in mind that the longer the hose, the harder it will be to collapse or expand.

Another area to consider is the thickness. Standard garden hoses have a diameter of 1 inch and while it is fine for General purposes of gardening, take a look at snake 3/4 inch if you need to deliver more water and pressure.

If you only need a snake once in a while, the snake vinyl might do the trick. Hoses-vinyl-cheaper than their rubber counterparts. Vinyl hoses are also more compact, lighter and less susceptible to depression. Speaking thus, the vinyl hoses do not provide such a great pressure, like a rubber hose, and they are almost as able to put to resist the elements.

By choosing attachments, you must read the product description. Your main goal is to make sure that the nozzle is the same diameter of the hose. If you have concerns related to environmental protection, look at the hoses that are advertised as BPA and phthalates. If you want to avoid the risk of bacterial reproduction in the water snake, look for a model with antibacterial protection.

4 khaki garden, you will save Your time and money
Here are four ways for maximum use of the garden hose even after it wyblaknięciu and consumption with holes:

First, the plug-in for toothpicks. Assuming that the hose for the yard pop up drain pins, stick a toothpick in the hole and then break a toothpick. You can reinforce it with duct tape, but the principle is that water will swell the wood, closing the flow until, until you get a sealed road.

Next stand on a tree branch. Bend are the main cause of leaks in garden hoses, so one of the ways to avoid them is twisting of the hose , and then find a nearby tree branch, and wrapping it around the wrapped hose.

The third that of sprinklers, with no turns. If you have an old hose that you want to spend, drill a hole in the rubber – or plastic – the two feet from about ten feet from the nozzle. When you’re finished, you’ll have the sprinkler. Just make sure the holes are lined up and that you can tighten the hose on both ends that was simple and directed upwards.

Fourth, Rubberized grip. When the hose is not suitable for use, it can be cut into pieces, each of which can be used to create a soft holder that can be wrapped around the paint, and even the chain swing. You can also use a piece of hose with a length of wire and two pieces of wood to put a newborn tree . At the end you can wrap the hose around any outside wires, thus protecting from nadepnięciem or przejechaniem car.

A brief history of the garden hose
The garden hose is something very American, regardless of whether we are talking about spraying the lawn, or connecting dispenser sprinkler and watch the children jump back and forth. The garden hose is a fence with a white torch. This dream house in the suburbs. And though there are many other snakes, including air hose and brake hose, garden hose is most associated with who we are and what we do.

Snakes have been around for centuries. Conceptual hoses are a closed tubular form of transport, usually on a particular type of liquid or gas. Most hoses made from reinforced rubber to withstand several bars pressure. In addition, most garden hoses are designed using the male and female pins on both ends. Connectors male and female from the hoses of the same size can be connected to each other, allowing you to increase the length of the device. This is especially useful when someone has a flat lawn or a rise of more than a hundred feet.

A typical garden hose fixed on the axle . At the turn of the twenty-first and twenty-first century most people uses the so-called Couplings for automatic lifting of the hose (without twisting). Quick couplings also allow connection of the second device to the axle. It reduces pressure, but increases the amount of work that can be performed.